Others say...

"PSP 2000 Traveler Case"
This case is awsome. It protects the PSP screen. It can hold up to two UMDs & two Memory Stick Pro Duos. You can play the PSP and still have it in the case. You can also change the position to watch a movie. It looks good and is portable. It is a strong case aswell. It looks good too. On the bottom of the case, it has two rubber cushions so it does not scratch the case or any surface the case is on. The only downfall is it gathers dust, and it gets hard to clean. Other then that, it is a very good case to use.

"Satisfied"
Good product, well built, and is holding up well after about 6 weeks of use. Some design issues, such as the plastic edges digging into your hands a little because of the way you need to hold the PSP but otherwise it does exactly what I wanted. One other issue is the reflective cover over the screen can sometimes make it difficult to see, but it is no worse than the actual screen on the PSP.

Good product.

"My two big bits on the case:"
Overall, I think this case tries to do a lot compared to the other cases I've seen on the market. So you really can't fault some one for that effort. Given the features, I can see why this case is so thick. What I still can't figure out is why Sony felt the need to include UMD and MS storage if the PSP is going to be locked down with the lens? There's a UMD travelers case on the market already and furthermore most PSP owners have more than two UMD's. Therefore, I don't see the need for this. I can imagine removing this extra storage would slim down the case substantially.



The thick lens that goes over the screen is VERY thick...~1/8". It looks like the lens you see on the store sample PSP. The benefits of this are that it keeps my fingers off the screen when I am frantically smashing the square button, and off the Home button should I press it accidentally. Secondly, the screen seems to magnify the image a bit. The image also seems somewhat sharper....can't put my finger on it yet. The USB port is virtually inaccessible. There's a hole cut out to access the port, but the hole is almost the same size as the port itself. Most USB plugs come with some form of casing and this is exactly what will prevent access to the port.

The Thicker Case makes the PSP much more comfortable to hold. The diminutive size of the PSP cramped my hands after hours of gaming. This also has the benefit of preventing accidentally rubbing up against the PSP power switch while gaming. On the other hand, with the case closed, turning the PSP off/on is almost impossible. The thicker case somewhat ineffectively attempts to guard the shoulder buttons against bumps with raised portion, but this also makes the buttons harder to reach. The shoulder buttons still protrude very slightly (~1/16") when pressed down. The case has to be opened to access the USB port (that is, if you can get to it). The back of the case resembles the PSP1000 with two rubber grips attached, keeping it from sliding around on smooth surfaces. At the bottom of the case where the clasps locks the case close, there is a cable channel to allow the unusual skype headset (or TV plug) configuration / cable to run across against the unit. The case also has plastic extensions /guards that will provide some protection for the plug against minor bumps or potential cuts. Finally, the locking clasp relies on two small hooks to keep the case closed. The button to unlock the case is almost flush against the case to prevent accidental bumps releasing the hooks.

The rubber-like inlay seems soft enough to take some minor bumps....but I am not sure about a drop from the table. Given the thick inlay, when the case is closed with all the compartments full the UMD is pressed up against the thick lens, which I'm not sure is a good idea. This inlay seems to be made with the same material as the soft rubber grips I mentioned.

The loose Double Hinge does not help keep the PSP stay upright. The texture and material of the surface has to be just right for the rubber feet to grip, and hold the angle shown in the pics above. However, the hinge seems bulky enough to sustain extensive use.

UMD and Memory stick slots are inaccessible when the PSP is locked into the case with the lens.

Assemblage of the case seems to be accomplished with snap-on joints. This means all the parts and pieces of the case can be separated with some force. This allows customizability, but it also means the whole thing could come apart easier on a collision.


"Depends on your needs"
This is a good case, it does protect your psp slim and screen very well.

For my needs however, it is a bit bulky. I don't need to carry two games and two memory cards around all the time, they could have trimmed some of the size off just by taking those slots off. As it is, every so often the memory card or games will pop out of the slots, they don't lock or click into the space provided, it's more of a form fitting soft plastic that sometimes doesn't hold.

The hinge on the top half is loose, it doesn't stay in place like some other cases do. While I didn't think much of it originally, over time it did become annoying as the top half rested on my knuckles while playing games.

I would recommend this case to anyone who does some traveling but doesn't want to carry around extra cases for games and memory cards, it's perfect for that.

Every day gamers may prefer something lighter, I wish Logitech would come out with a case for the slim, the one I had originally was perfect but is now to big for the slim.

"Decent case. Wish it was a bit cheaper"
I was a bit hesitant to pick up this case, but it does meet the criteria I was looking for. First off, I wanted a Hard case so I could throw it in a back pack and not worry about it. It has some extra space for for two additional UMD's, so I can keep 3 games with me (one in the system). It can be played while in the case (sometimes the extra thickness is nice for big hands) or easily taken out. And finally, it can convert into a stand for watching movies. This is great, because I like to use mine on the plane for movies. I have read other reviews that say it does not have a hole for the headphones. Mine has one, so I'm not sure what to say. Maybe a batch went out, without cutting that hole....Who knows. If you buy in the store, you'll be able to see the hole while in the package.

My only gripe, is I wish it was around $10.00. I showed my wife, and her first thought was "you payed $40 for the extended warranty/accidental coverage from my sony. Why waste any more on a case"

I would recommend it...